Nursing Elites

1. Two 5-ohm resistors are placed in series and wired into a 100-V power supply. What current flows through this circuit?

• A. 2 A
• B. 10 A
• C. 20 A
• D. 50 A

Correct answer: B

Rationale: In a series circuit, the total resistance is the sum of the individual resistances. Therefore, the total resistance in this circuit is 5 ohms + 5 ohms = 10 ohms. Using Ohm's Law (V = I × R), we can find the current (I) by dividing the voltage (V) by the total resistance (R). I = V / R = 100 V / 10 ohms = 10 A. Choice A (2 A) is incorrect because it does not account for the total resistance of the circuit. Choice C (20 A) and Choice D (50 A) are also incorrect as they provide values that are not consistent with the calculations based on the given values in the question.

2. The efficiency (η) of a heat engine is defined as the ratio of the net work done (Wnet) by the engine to the heat input (Qh) from the hot reservoir. The relationship is expressed as:

• A. η = Wnet / Qh
• B. η = Qh / Wnet
• C. η = Wnet x Qh
• D. η = (Wnet + Qh) / 2

Correct answer: A

Rationale: The correct formula for efficiency (η) of a heat engine is η = Wnet / Qh. Efficiency is defined as the ratio of the net work done by the engine (Wnet) to the heat input from the hot reservoir (Qh). This formula shows how effectively the engine converts heat into useful work, making choice A the correct answer. Choices B, C, and D present incorrect relationships between efficiency, net work done, and heat input, leading to their incorrectness.

3. A 60-watt lightbulb is powered by a 110-volt power source. What is the current being drawn?

• A. 0.55 amperes
• B. 1.83 amperes
• C. 50 amperes
• D. 6,600 amperes

Correct answer: A

Rationale: To calculate the current being drawn, use the formula I = P / V, where I is the current, P is the power in watts, and V is the voltage. Substituting the given values, I = 60 / 110 ≈ 0.55 amperes. Therefore, the current being drawn by the 60-watt lightbulb is approximately 0.55 amperes. Choice B, 1.83 amperes, is incorrect as it does not match the calculated value. Choices C and D, 50 amperes and 6,600 amperes, are significantly higher values and do not align with the expected current draw of a 60-watt lightbulb powered by a 110-volt source.

4. When calculating an object’s acceleration, what must you do?

• A. Divide the change in time by the velocity.
• B. Multiply the velocity by the time.
• C. Find the difference between the time and velocity.
• D. Divide the change in velocity by the change in time.

Correct answer: D

Rationale: When calculating an object's acceleration, you must divide the change in velocity by the change in time. Acceleration is defined as the rate of change of velocity with respect to time. By determining the ratio of the change in velocity to the change in time, you can ascertain how quickly the velocity of an object is changing, thereby finding its acceleration. Choice A is incorrect because acceleration is not calculated by dividing time by velocity. Choice B is incorrect as it describes multiplying velocity by time, which does not yield acceleration. Choice C is incorrect as finding the difference between time and velocity is not a method to calculate acceleration.

5. During adiabatic compression of a gas, what happens to its temperature?

• A. Remains constant
• B. Decreases
• C. Increases
• D. Becomes unpredictable without additional information

Correct answer: C

Rationale: During adiabatic compression, the gas's temperature increases. This is because no heat is exchanged with the surroundings, and all the work done on the gas results in an increase in internal energy. Choice A is incorrect because the temperature does not remain constant during adiabatic compression. Choice B is incorrect as the temperature does not decrease. Choice D is incorrect as the behavior of the gas's temperature during adiabatic compression is predictable based on the principles of thermodynamics.

Similar Questions