HESI A2
HESI Exams Quizlet Physics
1. The drag force (F_d) experienced by an object moving through a fluid depends on:
- A. Object's shape and size only
- B. Fluid properties and object velocity
- C. Depth of submersion only
- D. Buoyant force acting on the object
Correct answer: B
Rationale: The drag force experienced by an object moving through a fluid depends on multiple factors, including the object's shape, size, velocity, and the fluid's properties such as viscosity and density. Choices A, C, and D are incorrect because drag force is not solely determined by the object's shape and size, depth of submersion, or buoyant force acting on the object. The primary factors affecting drag force are the fluid properties and the object's velocity. Therefore, the correct answer is B.
2. A caterpillar starts moving at a rate of 14 in/hr. After 15 minutes, it is moving at a rate of 20 in/hr. What is the caterpillar’s rate of acceleration?
- A. 6 in/hr²
- B. 12 in/hr²
- C. 24 in/hr²
- D. 280 in/hr²
Correct answer: C
Rationale: Acceleration is the change in velocity over time. The change in velocity for the caterpillar is 20 in/hr - 14 in/hr = 6 in/hr. Since this change occurred over 15 minutes (or 0.25 hours), the acceleration can be calculated as (6 in/hr) / (0.25 hr) = 24 in/hr². Therefore, the caterpillar's rate of acceleration is 24 in/hr², which corresponds to choice C. Choice A, 6 in/hr², is incorrect as it does not account for the time factor and the correct calculation. Choice B, 12 in/hr², is incorrect as it doubles the correct acceleration value. Choice D, 280 in/hr², is significantly higher than the correct value, indicating a calculation error.
3. During adiabatic compression of a gas, what happens to its temperature?
- A. Remains constant
- B. Decreases
- C. Increases
- D. Becomes unpredictable without additional information
Correct answer: C
Rationale: During adiabatic compression, the gas's temperature increases. This is because no heat is exchanged with the surroundings, and all the work done on the gas results in an increase in internal energy. Choice A is incorrect because the temperature does not remain constant during adiabatic compression. Choice B is incorrect as the temperature does not decrease. Choice D is incorrect as the behavior of the gas's temperature during adiabatic compression is predictable based on the principles of thermodynamics.
4. When a dielectric material is inserted between the plates of a charged capacitor, what will happen to the capacitance?
- A. Increase
- B. Decrease
- C. Remain the same
- D. Become unpredictable
Correct answer: A
Rationale: When a dielectric material is inserted between the plates of a charged capacitor, the capacitance will increase. This is because the presence of a dielectric material reduces the electric field between the plates, allowing more charge to be stored for a given voltage, thus increasing the capacitance. Choice B is incorrect because adding a dielectric material increases capacitance. Choice C is incorrect because capacitance changes when a dielectric is added. Choice D is incorrect because the effect of a dielectric on capacitance is predictable.
5. The strength of a magnetic field is measured in units of:
- A. Amperes
- B. Tesla
- C. Volts
- D. Coulombs
Correct answer: B
Rationale: The Tesla (T) is the unit of measurement for the strength of a magnetic field. One Tesla is defined as one weber per square meter. Amperes (choice A) measure electric current, Volts (choice C) measure electric potential, and Coulombs (choice D) measure electric charge, making them incorrect choices for measuring the strength of a magnetic field.
Similar Questions
Access More Features
HESI A2 Basic
$49/ 30 days
- 3,000 Questions with answers
- 30 days access
HESI A2 Premium
$99/ 90 days
- Actual HESI A2 Questions
- 3,000 questions with answers
- 90 days access