Nursing Elites

1. A 60-watt lightbulb is powered by a 110-volt power source. What is the current being drawn?

• A. 0.55 amperes
• B. 1.83 amperes
• C. 50 amperes
• D. 6,600 amperes

Correct answer: A

Rationale: To calculate the current being drawn, use the formula I = P / V, where I is the current, P is the power in watts, and V is the voltage. Substituting the given values, I = 60 / 110 ≈ 0.55 amperes. Therefore, the current being drawn by the 60-watt lightbulb is approximately 0.55 amperes. Choice B, 1.83 amperes, is incorrect as it does not match the calculated value. Choices C and D, 50 amperes and 6,600 amperes, are significantly higher values and do not align with the expected current draw of a 60-watt lightbulb powered by a 110-volt source.

2. If a force of 12 kg stretches a spring by 3 cm, how far will the spring stretch when a force of 30 kg is applied?

• A. 6 cm
• B. 7.5 cm
• C. 9 cm
• D. 10.5 cm

Correct answer: B

Rationale: The extension of a spring is directly proportional to the force applied. In this case, the force increases from 12 kg to 30 kg, which is a 2.5 times increase. Therefore, the extension of the spring will also increase by 2.5 times. Given that the spring stretches 3 cm with a force of 12 kg, multiplying 3 cm by 2.5 gives us the extension of the spring when a force of 30 kg is applied, which equals 7.5 cm. Therefore, the correct answer is 7.5 cm. Choice A, 6 cm, is incorrect because it does not account for the proportional increase in force. Choice C, 9 cm, and Choice D, 10.5 cm, are incorrect as they overestimate the extension of the spring by not considering the direct proportionality between force and extension.

3. Given the four wires described here, which would you expect to have the greatest resistance?

• A. 1 km of American wire gauge 1; diameter 7.35 mm
• B. 1 km of American wire gauge 2; diameter 6.54 mm
• C. 1 km of American wire gauge 3; diameter 5.83 mm
• D. 1 km of American wire gauge 4; diameter 5.19 mm

Correct answer: D

Rationale: The wire with the greatest resistance is the one with the smallest diameter, as resistance is inversely proportional to cross-sectional area. Gauge 4 with a 5.19 mm diameter has the smallest diameter and, therefore, the greatest resistance. Choice A, B, and C have larger diameters compared to choice D, so they would have lower resistance values.

4. In hydraulic systems, Pascal's principle states that a pressure change applied to a confined incompressible fluid is:

• A. Amplified but loses energy
• B. Transmitted undiminished throughout the fluid
• C. Limited by the container size
• D. Dependent on the fluid type

Correct answer: B

Rationale: Pascal's principle states that when a pressure change is applied to a confined incompressible fluid, the resulting pressure change is transmitted undiminished throughout the fluid. This means that the pressure change will be the same at every point in the fluid, regardless of the container size or the type of fluid used. Therefore, choice B is the correct answer. Choices A, C, and D are incorrect because Pascal's principle specifically emphasizes the transmission of pressure without amplification, limitation by container size, or dependence on the fluid type.

5. Capillarity describes the tendency of fluids to rise or fall in narrow tubes. This phenomenon arises from the interplay of:

• A. Buoyancy and pressure differentials
• B. Density variations and compressibility of the fluid
• C. Viscous dissipation and inertial effects
• D. Surface tension at the liquid-gas interface and intermolecular forces

Correct answer: D

Rationale: Capillarity occurs due to surface tension and intermolecular forces between the liquid and the walls of the narrow tube. These forces cause the liquid to rise or fall depending on the cohesion and adhesion properties. Surface tension at the liquid-gas interface and intermolecular forces are responsible for capillary action, making choice D the correct answer. Choices A, B, and C are incorrect as they do not directly relate to the specific forces involved in capillarity.

Similar Questions