Nursing Elites

1. Given the four wires described here, which would you expect to have the greatest resistance?

• A. 1 km of American wire gauge 1; diameter 7.35 mm
• B. 1 km of American wire gauge 2; diameter 6.54 mm
• C. 1 km of American wire gauge 3; diameter 5.83 mm
• D. 1 km of American wire gauge 4; diameter 5.19 mm

Correct answer: D

Rationale: The wire with the greatest resistance is the one with the smallest diameter, as resistance is inversely proportional to cross-sectional area. Gauge 4 with a 5.19 mm diameter has the smallest diameter and, therefore, the greatest resistance. Choice A, B, and C have larger diameters compared to choice D, so they would have lower resistance values.

2. Longitudinal waves have vibrations that move ___________.

• A. at right angles to the direction of the vibrations
• B. in the direction opposite to that of the wave
• C. in the same direction as the wave
• D. in waves and troughs

Correct answer: C

Rationale: In longitudinal waves, the vibrations of particles occur in the same direction as the wave propagates. This means the particles move back and forth in the direction of the wave, creating compressions and rarefactions along the wave. Therefore, the correct choice is C, in the same direction as the wave. Choice A is incorrect because transverse waves, not longitudinal waves, have vibrations at right angles to the direction of wave propagation. Choice B is incorrect as it describes the motion in transverse waves. Choice D is incorrect as it is an inaccurate representation of how longitudinal waves propagate.

3. A 110-volt hair dryer delivers 1,525 watts of power. How many amperes does it draw?

• A. 167.75 amperes
• B. 1.635 amperes
• C. 1.415 amperes
• D. 13.9 amperes

Correct answer: D

Rationale: To determine the amperes drawn by the hair dryer, we use the formula: Amperes = Watts / Volts. The hair dryer operates at 1,525 watts with 110 volts. Dividing 1,525 watts by 110 volts yields 13.9 amperes. Therefore, the correct answer is 13.9 amperes. Choices A, B, and C are incorrect because they do not result from the correct calculation using the formula.

4. When analyzing a power plant, which of the following is NOT considered a part of the system?

• A. The fuel being burned.
• B. The working fluid (e.g., steam or water).
• C. The turbine that generates electricity.
• D. The surrounding air.

Correct answer: D

Rationale: In a power plant system, the components directly involved in the energy conversion process are considered part of the system. The fuel being burned provides the heat source, the working fluid transfers this heat energy, and the turbine converts it into mechanical energy to generate electricity. The surrounding air, while it may interact with the system, is not a component that directly participates in the energy conversion process within the power plant system. Therefore, the correct answer is D - The surrounding air. Choices A, B, and C are essential components of a power plant system as they play direct roles in the energy conversion process, unlike the surrounding air.

5. An object has a constant velocity of 50 m/s and travels for 10 s. What is the acceleration of the object?

• A. 0 m/s²
• B. 5 m/s²
• C. 60 m/s²
• D. 500 m/s²

Correct answer: A

Rationale: The acceleration of an object is defined as the rate of change of its velocity. When an object has a constant velocity, it means there is no change in its speed or direction. In this case, the object maintains a constant velocity of 50 m/s for 10 seconds, which implies that there is no change in velocity. Therefore, the acceleration of the object is 0 m/s² as there is no acceleration or deceleration happening. Choices B, C, and D are incorrect because acceleration is the change in velocity over time, and in this scenario of constant velocity, the acceleration is 0 m/s².

Similar Questions