Nursing Elites

1. A constant force is exerted on a stationary object. In this scenario, work is:

• A. Performed
• B. Not performed
• C. Partially performed
• D. Inconclusive without further information

Correct answer: B

Rationale: Work is only done when a force causes displacement. Since the object is stationary, no displacement occurs, and therefore, no work is performed. Choice A is incorrect because work requires both force and displacement. Choice C is incorrect as there is no partial work - work is either done or not done. Choice D is incorrect as the scenario provided is clear - the object is stationary, so no work is being performed.

2. Which conclusion can be drawn from Ohm’s law?

• A. Voltage and current are inversely proportional when resistance is constant.
• B. The ratio of the potential difference between the ends of a conductor to current is a constant, R.
• C. Voltage is the amount of charge that passes through a point per second.
• D. Power (P) can be calculated by multiplying current (I) by voltage (V).

Correct answer: B

Rationale: Ohm's law states that the ratio of the potential difference (voltage) between the ends of a conductor to the current flowing through it is a constant. Mathematically, this is represented as V = I x R, where V is voltage, I is current, and R is the constant resistance. Therefore, the correct conclusion that can be drawn from Ohm's law is that the ratio of the potential difference between the ends of a conductor to current is a constant, denoted as R. This relationship is fundamental to understanding the behavior of electrical circuits and the effect of resistance on voltage and current. Choice A is incorrect because Ohm's law actually states that voltage and current are directly proportional when resistance is constant. Choice C is incorrect because voltage is not the amount of charge that passes through a point per second; rather, it is the electric potential energy per unit charge. Choice D is incorrect because although power (P) can be calculated by multiplying current (I) by voltage (V), this is not a conclusion directly drawn from Ohm's law.

3. A system undergoes an isobaric process (constant pressure). In this process, the work done (W) by the system is:

• A. Zero, if the volume change (ΔV) is zero.
• B. Positive and equal to the pressure multiplied by the volume change (W = PΔV).
• C. Negative and equal to the pressure multiplied by the volume change.
• D. Independent of the pressure or volume change.

Correct answer: B

Rationale: In an isobaric process (constant pressure), the work done is given by the formula W = PΔV, where P is the pressure and ΔV is the change in volume. If the volume does not change, the work done is zero, not negative. Choice A is incorrect as it states the work done is zero when the volume change is zero, which is the correct condition for zero work. Choice C is incorrect as it incorrectly suggests that the work done is negative in an isobaric process. Choice D is incorrect as the work done in an isobaric process is indeed dependent on the volume change and pressure.

4. A closed system undergoes a cyclic process, returning to its initial state. What can be said about the net work done (Wnet) by the system over the entire cycle?

• A. Wnet is always positive.
• B. Wnet is always negative.
• C. Wnet can be positive, negative, or zero.
• D. Wnet is equal to the total heat transferred into the system (dQ ≠ 0 for a cycle).

Correct answer: C

Rationale: For a closed system undergoing a cyclic process and returning to its initial state, the net work done (Wnet) over the entire cycle can be positive, negative, or zero. This is because the work done is determined by the area enclosed by the cycle on a P-V diagram, and this area can be above, below, or intersecting the zero work axis, leading to positive, negative, or zero net work done. Choice A is incorrect because Wnet is not always positive; it depends on the specific path taken on the P-V diagram. Choice B is incorrect as Wnet is not always negative; it varies based on the enclosed area. Choice D is incorrect because Wnet is not necessarily equal to the total heat transferred into the system; it depends on the specifics of the cycle and is not a direct relationship.

5. What is the phenomenon by which light bends as it passes through a prism known as?

• A. Reflection
• B. Electrical conduction
• C. Diffraction
• D. Refraction

Correct answer: D

Rationale: Refraction is the phenomenon by which light bends as it passes through a prism or any other medium boundary. When light transitions from one medium to another, such as air to glass in the case of a prism, it changes speed and direction due to the change in the medium's refractive index. This change in speed causes the light to bend. Reflection, on the other hand, is the bouncing back of light when it hits a surface. Diffraction refers to the bending of light around obstacles or through narrow openings. Electrical conduction involves the movement of electrically charged particles through a conductor, which is unrelated to the bending of light.

Similar Questions