Nursing Elites

1. A 5-kg block is suspended from a spring, causing the spring to stretch 10 cm from equilibrium. What is the spring constant for this spring?

• A. 4.9 N/cm
• B. 9.8 N/cm
• C. 49 N/cm
• D. 50 N/cm

Correct answer: C

Rationale: The spring constant (k) can be calculated using Hooke's Law formula: F = -kx, where F is the force applied, k is the spring constant, and x is the displacement from equilibrium. In this case, the force applied is equal to the weight of the block, F = mg, where m = mass of the block = 5 kg and g = acceleration due to gravity = 9.8 m/s^2. The displacement x = 10 cm = 0.1 m. Substituting the values, we have: 5 kg * 9.8 m/s^2 = k * 0.1 m. Solving for k gives k = 5 * 9.8 / 0.1 = 49 N/m. Therefore, the spring constant for this spring is 49 N/cm. Choice A (4.9 N/cm) is incorrect because it is one decimal place lower than the correct answer. Choice B (9.8 N/cm) is incorrect as it does not account for the correct calculation based on the given information. Choice D (50 N/cm) is incorrect because it is slightly higher than the accurate value obtained through the calculations.

2. When a fluid encounters a bluff body (e.g., a car), the flow can separate behind the object, creating a region of low pressure. This phenomenon is known as:

• A. Cavitation
• B. Boundary layer separation
• C. Bernoulli effect per se
• D. Drag crisis

Correct answer: B

Rationale: The correct answer is B: Boundary layer separation. Boundary layer separation occurs when the flow of fluid detaches from the surface of a bluff body, leading to a low-pressure region behind the object. This separation creates a wake region with reduced pressure. Choice A, Cavitation, refers to the formation of vapor bubbles in a fluid and is not relevant in this context. Choice C, Bernoulli effect per se, does not specifically describe the phenomenon of flow separation behind a bluff body. Choice D, Drag crisis, is not the term used to describe the creation of a low-pressure region due to flow separation.

3. A concave mirror with a focal length of 2 cm forms a real image of an object at an image distance of 6 cm. What is the object's distance from the mirror?

• A. 3 cm
• B. 6 cm
• C. 12 cm
• D. 30 cm

Correct answer: B

Rationale: The mirror formula, 1/f = 1/do + 1/di, can be used to solve for the object distance. Given that the focal length (f) is 2 cm and the image distance (di) is 6 cm, we can substitute these values into the formula to find the object distance. Plugging in f = 2 cm and di = 6 cm into the formula gives us 1/2 = 1/do + 1/6. Solving for do, we get do = 6 cm. Therefore, the object's distance from the mirror is 6 cm. Choice A (3 cm), Choice C (12 cm), and Choice D (30 cm) are incorrect distances as the correct object distance is determined to be 6 cm.

4. Why doesn’t a raindrop accelerate as it approaches the ground?

• A. Gravity pulls it down at a constant rate.
• B. Air resistance counteracts the gravitational force.
• C. Its mass decreases, decreasing its speed.
• D. Objects in motion decelerate over distance.

Correct answer: B

Rationale: The correct answer is B. As a raindrop falls, it experiences air resistance which counteracts the gravitational force pulling it down. This balancing of forces prevents the raindrop from accelerating further as it approaches the ground. Choice A is incorrect because while gravity is pulling the raindrop down, air resistance opposes this force. Choice C is incorrect as the mass of the raindrop remains constant during its fall. Choice D is incorrect because objects in motion may decelerate due to various factors, but in this case, the focus is on why the raindrop doesn't accelerate.

5. What is the diameter of a loop if its radius is 6 meters?

• A. 6 m
• B. 12 m
• C. 18 m
• D. 36 m

Correct answer: B

Rationale: The diameter of a loop is calculated by multiplying the radius by 2. Since the radius is 6 meters, the diameter is 6 × 2 = 12 meters. Therefore, the correct answer is 12 meters. Choice A (6 m) is the radius, not the diameter. Choices C (18 m) and D (36 m) are incorrect as they do not reflect the correct calculation for determining the diameter of a loop.

Similar Questions