Nursing Elites

1. What is the term for a genetic disorder caused by a mutation on the X chromosome?

• A. Autosomal dominant disorder
• B. Autosomal recessive disorder
• C. Sex-linked recessive disorder
• D. Sex-linked dominant disorder

Correct answer: C

Rationale: A genetic disorder caused by a mutation on the X chromosome is termed a sex-linked recessive disorder (Option C). This type of disorder is more commonly seen in males due to their single X chromosome, making them more vulnerable to X-linked mutations. Females have two X chromosomes, providing a protective effect against X-linked disorders.\n- Autosomal dominant disorders (Option A) result from a mutation in one copy of a gene on non-sex chromosomes (autosomes) and are not specifically related to the X chromosome.\n- Autosomal recessive disorders (Option B) occur due to mutations in both copies of a gene on autosomes, not on the X chromosome.\n- Sex-linked dominant disorders (Option D) are rare and lead to more severe symptoms in males as they only require one copy of the mutated gene on the X chromosome to express the disorder. However, this is not the term for a genetic disorder caused by an X chromosome mutation.

2. What is a monohybrid cross, and what is the ratio of dominant to recessive gene manifestation?

• A. A cross involving two traits, 9:3:3:1
• B. A cross involving one trait, 3:1
• C. A cross involving two traits, 1:2:1
• D. A cross involving one trait, 1:1

Correct answer: B

Rationale: A monohybrid cross is a genetic cross involving one trait. The ratio of dominant to recessive gene manifestation in the offspring is typically 3:1 when both parents are heterozygous. This ratio is the genotypic ratio, not just the phenotype ratio, where the dominant allele is present in 3 out of 4 offspring, and the recessive allele is present in 1 out of 4 offspring. Choice A is incorrect because it describes a dihybrid cross ratio. Choice C is incorrect as it represents the genotypic ratio for a monohybrid cross involving incomplete dominance. Choice D is incorrect as it does not reflect the typical ratio for a monohybrid cross.

3. A pendulum swings back and forth. What type of energy conversion occurs during its motion?

• A. Potential energy to kinetic energy and vice versa
• B. Thermal energy to mechanical energy and vice versa
• C. Chemical energy to electrical energy and vice versa
• D. Nuclear energy to radiant energy and vice versa

Correct answer: A

Rationale: As the pendulum swings back and forth, it undergoes a continuous conversion between potential energy (at the highest point of the swing) and kinetic energy (at the lowest point of the swing). At the highest point, the pendulum has maximum potential energy due to its height above the ground. As it swings down, this potential energy is converted into kinetic energy, which is the energy of motion. At the lowest point of the swing, the pendulum has maximum kinetic energy and minimal potential energy. The process repeats as the pendulum swings back in the opposite direction, demonstrating the conversion between potential and kinetic energy. Choices B, C, and D are incorrect because the energy conversion in a swinging pendulum primarily involves changes between potential and kinetic energy, not thermal, chemical, electrical, nuclear, or radiant energy.

4. What is the difference between constructive and destructive interference of waves?

• A. They have different effects on wave amplitude.
• B. Constructive interference increases amplitude, while destructive interference decreases it.
• C. They affect wave amplitudes differently depending on the wave type.
• D. Their impact is determined by the relative phase of the waves, not wave speed or amplitude.

Correct answer: B

Rationale: Constructive interference and destructive interference are two phenomena that occur when waves interact. Constructive interference leads to an increase in wave amplitude when two waves meet in phase, resulting in the alignment of peaks and troughs. This alignment results in the combined wave having a higher amplitude. On the other hand, destructive interference causes a decrease in amplitude as two waves meet out of phase, leading to their cancellation. When peaks align with troughs, they cancel each other out, resulting in a lower overall amplitude. This difference in effect on wave amplitude distinguishes between constructive and destructive interference. Choice A is incorrect because it does not specify the direction of change in amplitude for each type of interference. Choice C is incorrect as both constructive and destructive interference can occur in various types of waves, not affecting them differently based on wave type. Choice D is incorrect because while the relative phase of waves does determine the interference type, it is the amplitude that is affected by constructive and destructive interference, not the wave speed.

5. What is the function of fascia in muscle tissue?

• A. to enclose, protect, support, and separate muscle tissue
• B. to connect muscle tissue to bone
• C. to serve as the contractile unit of muscle
• D. to slide past the actin protein cells in muscle to create contraction

Correct answer: A

Rationale: The correct answer is A: 'to enclose, protect, support, and separate muscle tissue.' Fascia is a connective tissue that surrounds muscles, providing structural support, protecting them from friction and injury, and helping in movement. Choice B is incorrect as tendons are responsible for connecting muscle tissue to bone. Choice C is incorrect as the contractile unit of muscle is the sarcomere, not fascia. Choice D is incorrect as the process described relates to muscle contraction mechanisms involving actin and myosin, not the function of fascia.

Similar Questions